Set
Function
This API is used to set AI > Setup > Region Entrance configuration parameters.
Request Message
Parameter Description
| Parameter | Range | Type | Description |
|---|---|---|---|
| channel_info | JSON object | Channel Information JSON show as follow Table 2 | |
| page_type | “ChannelConfig”, “AarmConfig” | string | It is used to distinguish whether it is the data of the channel configuration page or the alarm configuration page, it is only required when Set |
| channel_max | int | Maximum number of channels |
| Parameter | Range | Type | Description |
|---|---|---|---|
| CH1 | Json Object | JSON show as follow Table 3 | |
| … | Json Object | ||
| IP_CH1 | Json Object | ||
| … | Json Object | ||
| WIFI_CH1 | Json Object | ||
| … | Json Object |
| Parameter | Range | Type | Description |
|---|---|---|---|
| status | "Offline","Online"， “Nonsupport” | string | Channel online status, only for digital channels. Note: When the channel is online, there is no such field |
| alarm_out | “Local->1”… ”Local->x” “IP_CH1->1”… “IP_CH1->2”… ” IP_CHx->1” ” IP_CHx->2” The number of channels depends on the capabilities of the device. | array | Alarm output channel Each array bit represents aalarm output channel with a string. Camera: Local->1: open, null value: close |
| latch_time | "10","20","40","60" | string | Alarm output time |
| record_enable | true, false | bool | Recording channel switching |
| record_channel | “CH1”…”CH1x” “IP_CH1”…” IP_CH1x” “WIFI_CH1”…” | array | Alarm output channel Channel alarm linkage switch. |
| post_recording | "30","60","120","300" | string | Video delay time |
| send_email | true, false | bool | Send Email switch |
| ftp_picture_upload | true, false | bool | Channel capture FTP upload switch (for NVR only) |
| ftp_video_upload | true, false | bool | Channel recording FTP upload switch (for NVR only) |
| picture_to_cloud | true, false | bool | Picture upload switch (for NVR only) |
| video_to_cloud | true, false | bool | Video cloud upload switch (for NVR only) |
| full_screen | bool | FullScreen switch (for NVR only) | |
| buzzer | "0","10","20","40","60" | string | Buzzer sounding time (for NVR only) |
| show_message | bool | Show Message switch (for NVR only) | |
| switch | true, false | bool | PID enable switch, false: close true: open |
| detection_type | "Motion" "Pedestrian" "Vehicle" "Pedestrian &Vehicle" | string | Detection type, human shape and vehicle shape (normal detection type) |
| detection_type | “Pedestrian” "Motor Vehicle" "Non-motorized Vehicle" | array | Detection type, human figure, motor vehicle, non-motor vehicle (machine is not human type) |
| sensitivity | 1-100 | int | Detection sensitivity |
| target_validity | 1-4 | int | Target validity |
| min_pixel | 64-1080 | int | Minimum pixel value |
| max_pixel | 320-1080 | int | Maximum pixel value |
| rule_info | JSON object | Single-channel information JSON is as follows Table 4 | |
| point_num | [min:max] | array | The number of points drawn in the area, minimum 3 points (min), maximum 8 points (max) |
| Parameter | Range | Type | Description |
|---|---|---|---|
| rule_number1 | Object | Rule number 1, the information JSON is displayed as follows Table 5 | |
| rule_number2 | Object | Rule number 2, the information JSON is displayed as follows Table 5 | |
| rule_number3 | Object | Rule number 3, the information JSON is displayed as follows Table 5 | |
| rule_number4 | Object | Rule number 4, the information JSON is displayed as follows Table 5 |
| Parameter | Range | Type | Description |
|---|---|---|---|
| rule_switch | bool | rule switch | |
| rule_rect | Object | Rectangle, the information JSON is as follows Table 6 | |
| point_num | [min:max] | array | The number of points drawn in the area, minimum 3 points (min), maximum 8 points (max) |
| Parameter | Range | Type | Description |
|---|---|---|---|
| x1 | 0-704 | short | x1 coordinate point |
| y1 | 0-576 | short | y1 coordinate point |
| x2 | 0-704 | short | x2 coordinate point |
| y2 | 0-576 | short | y2 coordinate point |
| x3 | 0-704 | short | x3 coordinate point |
| y3 | 0-576 | short | y3 coordinate point |
| x4 | 0-704 | short | x4 coordinate point |
| y4 | 0-576 | short | y4 coordinate point |
| x5 | 0-704 | short | x5 coordinate point |
| y5 | 0-576 | short | y5 coordinate point |
| x6 | 0-704 | short | x6 coordinate point |
| y6 | 0-576 | short | y6 coordinate point |
| x7 | 0-704 | short | x7 coordinate point |
| y7 | 0-576 | short | y7 coordinate point |
| x8 | 0-704 | short | x8 coordinate point |
| y8 | 0-576 | short | y8 coordinate point |
Sample:
POST /API/AI/Setup/RegionEntrance/Set HTTP/1.1
{
"version": "1.0",
"data": {
"channel_info": {
"CH1": {
"switch": true,
"sensitivity": 50,
"max_pixel": 640,
"min_pixel": 64,
"target_validity": 3,
"iva_lines": true,
"detection_type": [],
"rule_info": {
"rule_number1": {
"rule_switch": false,
"point_num": [
3,
8
],
"rule_rect": {
"x1": 0,
"y1": 0,
"x2": 0,
"y2": 0,
"x3": 0,
"y3": 0,
"x4": 0,
"y4": 0,
"x5": 0,
"y5": 0,
"x6": 0,
"y6": 0,
"x7": 0,
"y7": 0,
"x8": 0,
"y8": 0
},
"rule_number": "rule_number1"
},
"rule_number2": {
"rule_switch": false,
"point_num": [
3,
8
],
"rule_rect": {
"x1": 0,
"y1": 0,
"x2": 0,
"y2": 0,
"x3": 0,
"y3": 0,
"x4": 0,
"y4": 0,
"x5": 0,
"y5": 0,
"x6": 0,
"y6": 0,
"x7": 0,
"y7": 0,
"x8": 0,
"y8": 0
}
},
"rule_number3": {
"rule_switch": false,
"point_num": [
3,
8
],
"rule_rect": {
"x1": 0,
"y1": 0,
"x2": 0,
"y2": 0,
"x3": 0,
"y3": 0,
"x4": 0,
"y4": 0,
"x5": 0,
"y5": 0,
"x6": 0,
"y6": 0,
"x7": 0,
"y7": 0,
"x8": 0,
"y8": 0
}
},
"rule_number4": {
"rule_switch": false,
"point_num": [
3,
8
],
"rule_rect": {
"x1": 0,
"y1": 0,
"x2": 0,
"y2": 0,
"x3": 0,
"y3": 0,
"x4": 0,
"y4": 0,
"x5": 0,
"y5": 0,
"x6": 0,
"y6": 0,
"x7": 0,
"y7": 0,
"x8": 0,
"y8": 0
}
}
},
"chn_index": "CH1",
"page": "chn_pid_split",
"curPage": "chn_region_entrance",
"rule": {
"rule_switch": false,
"point_num": [
3,
8
],
"rule_rect": {
"x1": 0,
"y1": 0,
"x2": 0,
"y2": 0,
"x3": 0,
"y3": 0,
"x4": 0,
"y4": 0,
"x5": 0,
"y5": 0,
"x6": 0,
"y6": 0,
"x7": 0,
"y7": 0,
"x8": 0,
"y8": 0
},
"rule_number": "rule_number1"
}
}
},
"page_type": "ChannelConfig"
}
}
Response Message
Error_Code Response
Error Information JSON (show as follow Table 7) (cloud_video_upload_chn_limit The return information attached to the error code)
| Parameter | Range | Type | Description |
|---|---|---|---|
| cloud_video_is_used | 0~MAX_PARA_CHN_NUM | array | The channel number for which the cloud video upload function has been enabled |
| max_cloud_video_upload_num | MAX_CLOUD_VIDEO_RECORD_NUM | int | The maximum number of channels supported by cloud video upload |
Sample:
HTTP/1.1 200 OK
Content-Type: application/json
{
"result": "success",
"data": {}
}
Error Code
See Response Messages Body and Common error_code for more information.